jryan76
02-26-2009, 04:47 PM
Hi Guys!
I'm offering up a couple of recently completed pieces.
Both are priced at 125.00 (+3% Paypal) shipped in the Cont. U.S. Please add additional shipping for outside the Cont. U.S.
My Disclaimer:
Okay guys..I'm pretty much a newb to the knifemaking world. These are some of my first pieces, well..actually, they pretty much are my first pieces to be completed from start to finish. That said, the grinds arent perfect, the hand rubbing isnt perfect unfortunately. Just want to put that out there for any potential buyers.
They both come with lifetime tune ups and sharpening. And of course if you recieve it and its not to your 100% satisfaction..money back no questions asked.
First up is one of my friciton folders. Sold!
Heres the Specs:
Blade is 1084 at 2 1/4" from tip to handle
Handle is Green/black g10 measuring 3 1/4" with an overall length of 5 1/2".
There is an orange g10 back spacer.
Lanyard loops around the blade just as an extra measure to keep the blade closed in the pocket. There are no detent or lock on these, the friction is strong and it isnt likely to open anyhow, but this is just an extra safety device.
http://i175.photobucket.com/albums/w139/jryan_photo/BB2.jpg
http://i175.photobucket.com/albums/w139/jryan_photo/BB4.jpg
http://i175.photobucket.com/albums/w139/jryan_photo/BB5.jpg
http://i175.photobucket.com/albums/w139/jryan_photo/BB6.jpg
http://i175.photobucket.com/albums/w139/jryan_photo/BB7.jpg
http://i175.photobucket.com/albums/w139/jryan_photo/bb1.jpg
Next:
A small Utility fixed blade.
Specs:
2 5/8" from handle to tip of 1084 steel
Green/Black Blasted G10 handle: 3 1/4" at the longest point
S/S tubing
I did notice some dips sort of in the flat grind of this one. Probably due to working with a 1" platen. (all my stuff is ground on a Delta 1 x 42" grinder) I didnt feel they were too bad, but in the right light you can see them and feel them. Doesnt effect performance of the blade obviously and they are minor, but I want to make sure and point this out to the buyer. They appear about 3/4" the way up from the handle.
I was going to regrind the blade and then do the hand rub over, but I figured I'd just offer it here for what it is.
http://i175.photobucket.com/albums/w139/jryan_photo/DSCI0670.jpg
http://i175.photobucket.com/albums/w139/jryan_photo/DSCI0672.jpg
Thanks for looking!
I'm offering up a couple of recently completed pieces.
Both are priced at 125.00 (+3% Paypal) shipped in the Cont. U.S. Please add additional shipping for outside the Cont. U.S.
My Disclaimer:
Okay guys..I'm pretty much a newb to the knifemaking world. These are some of my first pieces, well..actually, they pretty much are my first pieces to be completed from start to finish. That said, the grinds arent perfect, the hand rubbing isnt perfect unfortunately. Just want to put that out there for any potential buyers.
They both come with lifetime tune ups and sharpening. And of course if you recieve it and its not to your 100% satisfaction..money back no questions asked.
First up is one of my friciton folders. Sold!
Heres the Specs:
Blade is 1084 at 2 1/4" from tip to handle
Handle is Green/black g10 measuring 3 1/4" with an overall length of 5 1/2".
There is an orange g10 back spacer.
Lanyard loops around the blade just as an extra measure to keep the blade closed in the pocket. There are no detent or lock on these, the friction is strong and it isnt likely to open anyhow, but this is just an extra safety device.
http://i175.photobucket.com/albums/w139/jryan_photo/BB2.jpg
http://i175.photobucket.com/albums/w139/jryan_photo/BB4.jpg
http://i175.photobucket.com/albums/w139/jryan_photo/BB5.jpg
http://i175.photobucket.com/albums/w139/jryan_photo/BB6.jpg
http://i175.photobucket.com/albums/w139/jryan_photo/BB7.jpg
http://i175.photobucket.com/albums/w139/jryan_photo/bb1.jpg
Next:
A small Utility fixed blade.
Specs:
2 5/8" from handle to tip of 1084 steel
Green/Black Blasted G10 handle: 3 1/4" at the longest point
S/S tubing
I did notice some dips sort of in the flat grind of this one. Probably due to working with a 1" platen. (all my stuff is ground on a Delta 1 x 42" grinder) I didnt feel they were too bad, but in the right light you can see them and feel them. Doesnt effect performance of the blade obviously and they are minor, but I want to make sure and point this out to the buyer. They appear about 3/4" the way up from the handle.
I was going to regrind the blade and then do the hand rub over, but I figured I'd just offer it here for what it is.
http://i175.photobucket.com/albums/w139/jryan_photo/DSCI0670.jpg
http://i175.photobucket.com/albums/w139/jryan_photo/DSCI0672.jpg
Thanks for looking!